急寻电工有偿更换 GFI

juliedqq

如题。公寓在Downtown.   请电工师傅帮忙。急!急!急!
请电780-914-8382.谢谢。

happylife88

What is GFI?

ballard

多大事情 必须电工

ballard

Homedepot 买同型号的 拧上就是

不紧张

ballard 发表于 2014-3-21 17:10
' j9 T1 S0 ~& y/ CHomedepot 买同型号的 拧上就是

就是就是
: i5 Q& F. o) Y  w
. l1 o' V2 w0 s* U) }虽然不知道什么是 GFI

但既然 你说了   肯定不是啥大事

Scottl

ballard 发表于 2014-3-21 17:10
# @5 \. }0 |( Z9 G! j8 v1 y# M: jHomedepot 买同型号的 拧上就是

: j& [( \) C9 q- j3 O9 D* u' \" f估计市里要来验收吧。
/ C+ e, |* G# O% R3 X7 b: K' f
% v+ s7 k/ w  k( s光换插座不行，要从电器柜开始接线。
+ n7 e1 Z& _! r- w: m. ^7 \
还有顺便提醒一下，去年新规定，卧室的插座要AFCI的，我申请Permit时才知道。

kingsnake

ballard 发表于 2014-3-21 17:10
Homedepot 买同型号的 拧上就是

對。十分簡單。
' l. u; k. D% \+ r+ Q, w, T6 q把 普通的 換上 GFI 的就行了，記得先關掉 breaker。
5 t: ~4 g  f9 @9 C9 T
Instructions
1 Go to your service panel and locate the circuit breaker for the area in which you will be working. Shut the breaker off. If your breakers aren't labeled, turn them off one by one until you find the breaker for your area.
2 Test to confirm that the power is off within the outlet. Insert the tip of the voltage sensor carefully into the outlet. If it doesn't light up, the power is off.
% M8 }$ N1 ?+ K0 {7 F# zIf it does light up, the power is still on. Check your service panel and turn off another likely circuit breaker. Use the voltage sensor to re-test the outlet. Do not proceed with these instructions until you are confident that the power is off.
3 Remove the outlet cover plate and unscrew the mounting screws, taking care not to touch the wires or terminals. Remove the outlet receptacle.
4 Test both of the wires coming out of the receptacle with your voltage sensor. Testing the outlet for power is not always accurate, as the receptacle may be damaged but still contain live wires.
/ o1 H, Y6 F1 J' h& Y& L5 Unscrew the terminals from the outlet and pull away the wires, taking care not to twist them. If you see any nicks or other damage to the wires, use the wire strippers to snip off their ends and re-strip them.
, Z/ d. P; }% p* @ 6 Take your GFCI outlet and turn it so that the back faces you. You will see one set of terminals marked "line," and one marked "load." Connect your wires to the terminals marked "line." The neutral (white) wire connects to the silver terminal, and the hot (black) wire goes to the brass terminal.
6 p7 B; p4 E9 p2 O, S; n 7 Place the GFCI outlet receptacle back into the wall. Replace the screws and cover plate.
, y& w! E. x# W% P 8 Turn the circuit breaker back on. Test the new outlet for power by inserting your voltage sensor into the outlet. If it lights up, you have succeeded. If there is no current, turn the breaker back off, remove the outlet from the wall, and check your connections.

ballard

Scottl 发表于 2014-3-21 17:31
估计市里要来验收吧。

光换插座不行，要从电器柜开始接线。

5 t( p, ~" Q. A  z
* x' D: n0 A# O: R; `验收需要电工签名么

如果不需要。视频下我告诉他安装方法

ballard

kingsnake 发表于 2014-3-21 18:12
. `$ V& {/ W9 b/ F9 U1 W( C4 }對。十分簡單。
把 普通的 換上 GFI 的就行了，記得先關掉 breaker。

说明很详细
* v, C3 p' X. ^9 I; w5 J
! j) L# M/ g# k5 p建议 如果不自信 找一个人 看着操作者
. D- w, y9 e- A, p% N* O
7 ~# f7 A; Z; Z4 M; Y: q触电 拉一把，这个加在所以说明最前面。
  |: q: r) Z% P4 A
110 伏特 不是很可怕  我被220电几次 确实不爽， 电一下
" R$ ^5 X4 @! S2 L2 _. |. c- z: Q
1 y# \4 X& U) Z- A7 |很恼火。哈哈哈

贾佃工

ballard 发表于 2014-3-21 18:20
说明很详细
/ {1 D0 h  H5 o# n! [2 X& W# a$ U
- v( y5 @. w5 R1 v5 _/ ]' m建议 如果不自信 找一个人 看着操作者

! [8 P7 t: t7 g8 j6 X; l别说胡话了，110伏绝对会电死人。这次运气好不等于下次运气也好。

yanngoyan

中学物理老师教过，36伏以上就能电死人，不过没试过。