 鲜花( 48)  鸡蛋( 0)
|
also check this:
, V/ k& ~3 O0 U$ f- k( C4 K: m5 a5 |0 a) u
Pressing for one second arms the system by activating the8 {, s, i, F, }% `
starter kill and locking the doors (if the door locks are connected).
% Y$ W- a" n N* }0 T ?The horn will honk (if connected) and the parking lights will flash
; J* K8 D% Q& L8 n5 y; h9 zonce to confirm arming of the system. While the system is armed,6 j9 i$ v# {! `) n. K# @. c& m
the status LED will flash once per second. The Failsafe® Starter Kill
) N: c$ D2 }; H. N% e) i# V" _ s; I(if installed) will also prevent the vehicle’s starter from cranking.
5 Y. z! O1 L8 `( Q( ZArming
6 R# M4 N% x, f2 T$ p7 m: g9 p© 2005 Directed Electronics—all rights reserved 93 j2 w2 t2 e5 V
The system can also be programmed to arm the optional Failsafe®* ~ E) B# b' ^& ~% ^, J0 s: Q
Starter Kill automatically (called Passive Mode). If the system has0 ]& c1 N$ d4 T9 S! i
been programmed for Passive Mode, the Failsafe® Starter Kill will& {0 R f+ ~; k0 @
automatically activate 30 seconds after the ignition has been ^: t/ G& V o
turned off. After the ignition has been turned off, the status LED
. w* ]' Q5 U+ ]3 Hwill flash rapidly to indicate that the system is in Passive Mode.
, N9 A# w' s: M% Q- Q2 TIf Passive Mode has been programmed on, then it is also possible6 U1 O0 o, E/ m% ~. V$ w
to program the system for Passive Locking. With Passive Locking,# P6 S1 }5 K4 d) A" m
the vehicle doors lock automatically at the same time that the Failsafe®
* A! z9 j+ Y3 P P7 KStarter Kill is activated. If Passive Locking is programmed on, care8 x0 C5 _% w @ p
must be taken to prevent the keys from being locked in the vehicle.
+ q( x4 ]6 [2 N3 iNOTE: For Passive Mode to be effective, the Failsafe® Starter Kill relay" I! @! I" x `! P9 x* \
must be installed.
2 H2 ?8 @2 B; Q6 x$ f2 PPressing for one second disarms the system and unlocks the
- X3 N s5 j7 ] U1 ~8 Ydoors (if connected). The horn will honk twice (if connected) and" T" X+ H! }- E
the parking lights will flash twice to confirm disarming of the system.: l1 U& K4 M' B6 `4 \
The optional Failsafe® Starter Kill will be deactivated. The status
$ r2 o2 Q7 K0 |1 Q2 XLED will turn off, unless the system is programmed for Passive
4 Z; L& Z) _& q1 S. d3 {! U0 yMode. In Passive Mode, the status LED will flash rapidly when the
& o1 o; W0 D4 W/ w, {/ I0 Isystem is disarmed. This indicates that the system will re-engage! `1 E G8 `2 _, x' a( R( I
the starter kill and re-lock the doors (if Passive Locking has been. e/ o8 U) T, u' W# l, w, B" w! |
programmed) in 30 seconds unless the ignition is turned on.; ~8 Z7 y! d0 x0 Z- h
Disarming) `. Y9 p# c/ T# E( G) x
10 © 2005 Directed Electronics—all rights reserved3 F: A$ N. j [2 S9 `/ ]7 N8 D
If your remote transmitter is lost or damaged, you can manually
( X! D/ Z3 k0 F8 Qoverride the starter kill. To do this, you must have the vehicle's
9 Z- `5 V L0 `" J$ hignition key and know where the Valet button is located. Be sure
! l. X2 @5 I t7 ^' e; q: Kto check with the installer for the location of the Valet button.
. c5 V: ^2 s% @: B; d4 nTo override the starter kill, turn
0 j3 ^: ]) z: s5 V4 [the ignition on and press the
- D+ D8 j$ }6 c7 ~* F5 Q: DValet button within 10 seconds.2 v1 ]. ~ ~( y; f' f( Z
The status LED will stop flashing
" o4 l9 A* s# i, F# |) L A0 h gand the vehicle should start. If it does not start,
1 _ B |1 T! |4 Wyou may have waited too long; turn the ignition off and repeat the" R6 X# M# ]. H
process.
( S% D, M9 u. O# A8 S( tLOCATION OF VALET BUTTON_____________________________7 S: \7 y4 E' a; J
You can prevent your system from automatically activating the: n) X+ v0 t! e4 ^
Failsafe® Starter Kill and locking the doors by using Valet Mode.2 F/ z T6 m0 o1 Z
This is very useful when washing the vehicle or having it serviced.$ ?0 W* _& X7 x% d, S, h
In Valet Mode, the starter kill cannot be activated, even with the7 M' a/ T% i7 m3 a) L
transmitter, but all convenience functions (door locks, remote
+ I! q: y) s* e rstart, etc.) will continue to work normally. |
|